leydis16

[hhm1020]

It is well known scientific floor installation is a key factor to ensure the life of the floor. However, many owners of floor coverings due to the lack of knowledge on how to install flooring acceptance quality bewilderment.
1, see the color of the floor are the same. If the color is too large, directly affect the appearance, you can ask exchange; if the color is too uniform, almost no color, it is the floor pattern depends on whether the same surface. If the pattern is almost the same, then there may be craft wooden floor, rather than the so-called precious wood species of flooring material. Now some flooring suppliers by using [url= http://externalfloor.co.uk/soild-board/14.html ] cheap high-density polyethylene decking boards[/url], but in the surface layer of valuable wood species stick to shoddy veneer, that is to moisture, in fact, is the fear of being seen negative and positive pattern is inconsistent .
2, to see the floor if there is sound, acceptance on the floor back and forth, the pace should be increased, especially in parts of the wall parts and openings to pay more attention and acceptance, the site found the sound to repeat the move, to determine the specific location of the sound, do good marks. In that case, you can request removal of resurfacing. There are sounds of the site, construction workers are in the construction process, operation and use of non-standard material substandard caused. Mainly in non-standard operation is not firmly fixed keel; material failure is mainly reflected in the keel without drying. Some of the keel construction decoration and construction unit with without drying, the surface has dried traces, in fact, did not do. High moisture content of the keel, the wood natural drying process volume will be reduced, resulting in loose.
3. Acceptance floor deformation, warping, acceptance method is to use two meters long ruler, covering roof terrace should not exceed 3 mm. Pumping a few more measurements, if the passing rate of 80% or more are deemed qualified, on the contrary, that is unacceptable. Sometimes we find a local bagging the floor: If the floor is wood, it is because the shop floor too tight or too dry (moisture content is too low); if it is laminate flooring, it is poor quality of the floor. So the floor bagging is a serious quality problems.
4, baseboard acceptance: ≤2 mm gap between the baseboard and door frames; ≤1 mm spacing between the baseboard patchwork; gap baseboard and the floor surface should be in the range of 3 mm to 5 mm; skirting line deduction mouth height difference should ≤1 mm.
5, door buckle acceptance: door buckle should be installed directly below the door, close the door, do not stay outside edge is appropriate, buckle and bottom of the gap between the door 3 mm -7 mm, able to open the door closable. Buckle installation should be strong, stable, kicking at the middle of the buckle and check whether both sides of the buckle or loose tilt, any abnormal sound.
6, the final acceptance of the floor surface if there is termite eyes, cracks, scratches. Common is due to keel untreated, there are worms. Isochronous found moth eye, the floor has been almost a bore; cracks and scratches to see that. Specification: floor gap should not exceed 0.5 mm; the decoration is mainly caused by rough scratch, as with waxing method still can not be repaired, it must be replaced. Wood flooring material varieties, grades meet the design requirements, the moisture content should be around 10 percent, surgery keel, skids made embalmed, wood keel to install a solid, straight, spacing and fixation methods in line with regulatory requirements, the board nail shop solid, no loose, solid paste, without hollowing, use plastic varieties to meet regulatory requirements.
Visually inspect the wood floor surface planing, polishing, no scars, clear Russian stubble and burrs, pattern, consistent surface layer of edible vegetable oil color, paving the right direction, [url=http://syntheticboard.com/wood-floor/4165.html ]outdoor engineered wood railing[/url], the joint position shifted, clean surface. The laying of the skirting board joints tight, smooth surface, uniform height and thickness of the wall. With 2 meters by foot inspection, ground flatness error of less than 1 mm, slit width less than 0.3 mm, the skirting board mouth flatness error of less than 3 mm, patchwork flatness error of less than 2 mm.

[Reklama]

[Reklama]

Zobacz też :



_____________________
Katalog Stron - Dodaj stronę ZA DARMO
Darmowy Katalog Stron
Ceny akcji
Liczby Fibonacciego na rynku FOREX, czyli Harmonic Trading bez tajemnic

[Reklama]